+- RoboDK Forum (//www.sinclairbody.com/forum)
+-- Forum: RoboDK (EN) (//www.sinclairbody.com/forum/Forum-RoboDK-EN)
+ - - -论坛:通用RoboDK问题(//www.sinclairbody.com/forum/Forum-General-questions-about-RoboDK)
+--- Thread: Wrong tool orientation using Mastercam plugin (/Thread-Wrong-tool-orientation-using-Mastercam-plugin)
Wrong tool orientation using Mastercam plugin-FredericH-03-05-2019
Dear RoboDK Team,
i am quiet new to the Topic.
I try to get a 5 axis G-Code running via the mastercam plugin but I have problems to get the right 5 axis tool orientation. When generating the robot programm it always outputs a toolpath where the tool orientation ist Z+ (vertical in my coordinate system).
I tried to reproduce it with an easy geometry. So i tried to get a toolpath for an easy circle which is placed on a side of a vertical surface. So the tool orientation should be horizontal. The simulation in Mastercam shows the right result but in RoboDK the circle is again horizontal an the toolorientation ist vertical ( Z+). I attached some pictures for this example.
The same with 5 axis simultaneous toolpaths. Doesn´t matter which toolorientations were given in Mastercam. The Mastercam-Simulation shows the right toolpath but in Robodk its always vertical/ Z+
I use Mastercam 2019 ,the default "Mill Default MM" post processor and RoboDK Version 3.6.0
Looking forward to your reply.
Thanks!
RE: Wrong tool orientation using Mastercam plugin-Albert-03-05-2019
Hi Frederic,
It look like the problem is with the orientation of the reference/datum and not the tool.
Can you provide Mastercam and RoboDK files so that we can reproduce this issue? We'll fix it as soon as possible.
Albert
RE: Wrong tool orientation using Mastercam plugin-FredericH-03-05-2019
Hi Albert,
thanks for the quick reply.
Attached you can find the Mastercam and the RoboDK files.
Thanks.
Frederic
RE: Wrong tool orientation using Mastercam plugin-Albert-03-07-2019
Hi Frederic,
I'm unable to reproduce this issue. I see the same toolpath and tool orientation in both Mastercam and RoboDK, as shown in the following image:
[attachment=193]
What Mastercam version are you using?
I also recommend you to uninstall RoboDK, download and install again.
Albert
RE: Wrong tool orientation using Mastercam plugin-Albert-03-07-2019
Just to clarify:
Did you use RoboDK's plugin for Mastercam?
More information here:
//www.sinclairbody.com/doc/en/Plugin-Mastercam.html#McamIntro
If you prefer to not use the plugin you can just load Mastercam's NCI files.
RE: Wrong tool orientation using Mastercam plugin-FredericH-03-07-2019
Thanks for your fast response.
I am using Mastercam 2019 with the RoboDK Plugin. I will try to reinstall RoboDK.
Reinstalled RoboDK.
I tried it again without using the Plugin. Just directly importing the NC-Code. But tool orientation ist still vertical and as you can see the result ist quiet strange because it isn´t even a circle in the horizontal level anymore.
What "Part" did you add to Frame 2?
Ah got it! When I use the generated NC-Code it gives the wrong result seen above. When I use the Plugin and use the Mastercam NCI Code than it works.
RE: Wrong tool orientation using Mastercam plugin-Albert-03-07-2019
Thank you for your feedback. I'm happy to hear you were able to make it work using NCI files.
If you prefer using NC files or G-code it would be better to use a generic 5-axis machine configuration with a generic 5-axis G-code post processor.