+- RoboDK Forum (//www.sinclairbody.com/forum)
+-- Forum: RoboDK (EN) (//www.sinclairbody.com/forum/Forum-RoboDK-EN)
abo血型+——论坛:一般问题ut RoboDK (//www.sinclairbody.com/forum/Forum-General-questions-about-RoboDK)
+--- Thread: Connection Fault with Yaskawa (/Thread-Connection-Fault-with-Yaskawa)
Connection Fault with Yaskawa-Otto_Scho-01-18-2021
Hello,
I still have a problem with the connection between RoboDK and the Roboter.
As you see in the photos, the Ip address of Robot 192.168.1.31, and for my computer 192.168.1.45.
Pinging is OK. all firewalls are deactivated.
Hint: i set the Debug_Print=true
RE: Connection Fault with Yaskawa-Jeremy-01-19-2021
Hi Otto,
Did you look at this section of the documentation:
//www.sinclairbody.com/doc/en/Robots-Motoman.html#Motoman
Jeremy
RE: Connection Fault with Yaskawa-Otto_Scho-01-19-2021
(01-19-2021, 03:53 AM)Jeremy Wrote:Hi Otto,
Did you look at this section of the documentation:
//www.sinclairbody.com/doc/en/Robots-Motoman.html#Motoman
Jeremy
Hi Jeremy,
Thank you for your Answer. Yes, I did and I followed the instructions step by step but unfortunately no benefits.
Otto
RE: Connection Fault with Yaskawa-Phillip-01-19-2021
Hello, you said you turned Debug_Print=True so I assume you know how to edit the config file, could you post a screenshot of the begining of the driver log, you can completely reset the driver by double clicking disconnect in the connection panel.
RE: Connection Fault with Yaskawa-Otto_Scho-01-19-2021
Hi Philip,
Please find the attached files. I hope I posted the write one ;-)
Thank you
RE: Connection Fault with Yaskawa-Phillip-01-20-2021
It appears the controller isn't responding to initial request to make sure the robot exists, do you know what controller your using with the robot? (DX100,DX200,YRC1000,etc)
RE: Connection Fault with Yaskawa-Otto_Scho-01-21-2021
(01-20-2021, 05:38 PM)Phillip Wrote:It appears the controller isn't responding to initial request to make sure the robot exists, do you know what controller your using with the robot? (DX100,DX200,YRC1000,etc)
The Controller is DX100
The Robot is MH50
I already sent the (All.PRM) to Motoman and they activated the Ethernet-Parameter for me.
So now when I ping the IP address of the Controller, I get correctly the feedback from the controller.
But The connection failed.
Thank you ..
RE: Connection Fault with Yaskawa-Otto_Scho-02-02-2021
(01-20-2021, 05:38 PM)Phillip Wrote:It appears the controller isn't responding to initial request to make sure the robot exists, do you know what controller your using with the robot? (DX100,DX200,YRC1000,etc)
Hi Philip,
DO you have an idea how can I solve this issue?
Thank you
Otto
RE: Connection Fault with Yaskawa-Phillip-02-12-2021
(02-02-2021, 10:40 AM)Otto_Scho写道:(01-20-2021, 05:38 PM)Phillip Wrote:It appears the controller isn't responding to initial request to make sure the robot exists, do you know what controller your using with the robot? (DX100,DX200,YRC1000,etc)
Hi Philip,
DO you have an idea how can I solve this issue?
Thank you
Otto
Reading manuals for motoman robots I see a note that the serial communication needs to be disabled for ethernet communication to work, this is done by setting parameter FD077 to 1 and FD078 to 1. Can you verify the value on the controller?